Solve Connectivity Problems with Linksys RE6300 Setup and RE7000 Reset

In the event that your Wi-Fi fails after every few minutes or the speed is slow even when you are within close range of the router, then there are likely issues that are going on with your range extender. The Linksys RE6300 and RE7000 are both good when it comes to range extension, and are good to install, but tend to malfunction or the software bugs. This tutorial follows a step-by-step real world process of getting back into your Wi-Fi with easy set up procedures and reset procedures with Linksys RE6300 and RE7000.

Installation of and Linksys RE6300

Let's ask you to now go through the process in the same manner as you would in real life and not muddy it up.

Step 1: Plug It In and Wait

Plug in your RE6300 into a wall socket in the middle between your main router and a location that has poor Wi-Fi connectivity. Wait till the indicator light becomes orange or blinking amber. That is, it is prepared to be installed.

Step 2: Join to the Extender Network.

Open the Wi-Fi list on your phone or laptop and see if you can find a network that has the name such as "Linksys Extender Setup - xxx." Connect to it.

Step 3: Open the Setup Page

At this point, open a browser and either type in extender.linksys.com or the IP address displayed on the label of the device. In case the page fails to load, switch off mobile data or use a laptop, not a phone- it is more reliable.

Step 4: Follow the On-Screen Set-up.

That is when you will find the setup wizard. Choose your primary network of Wi-Fi in the list and write the password. This is to connect or tie the Linksys RE6300 setup to your current network. 

Step 5: Finalize the Setup

On hitting the button of finish, the extender will restart. As soon as the light turns solid green, The Linksys RE6300 is finished. Now again connect your devices to the extended network and verify the signal strength.

Why a Reset solves So Many RE7000 Problems.

When you are using a Linksys RE7000 and randomly loses connection, or displays No Internet, or will not connect to your router, it is normally sorted out by resetting the device. A reset deletes all the preservation made and restores it to factory settings. This will be handy in case you have modified router settings, passwords or firmware.

Linksys RE7000: How to startup a fresh installation

The reset used to be done is easy and must be done right:

Step 1: Power It On

Plug in RE7000 and wait till the light is stable (not blinking).

Step 2: Hold and Press the Reset Button

It has a reset button that can be pressed with a pin or paperclip on the side or bottom. Keep this length of time 10 seconds until the light begins blinking.

Step 3: Wait for Reboot

Push the button and allow some time (one to two minutes). After the reboot, the extender will be defaulted.

You may now proceed to make a new setup by following the same procedure as the linksys re6300 set up.

User Guide

In case the set up page is not opened, then do the following brief troubleshooting:

• Turn off VPN or antivirus.

• Clear your browser cache.

• Use a different browser such as firefox or edge.

• Ensure that you are not connected to mobile data.

Firmware Updates

The old version of a firmware can also lead to slowing down the speed or occasionally sudden disconnection. It should never be installed without first checking updates after being set up or in case of a resetting of the Linksys RE7000:

• Use your administrative account.

• Go to the Firmware Update section of the Administration.

• There should be no steps to do in case of an update, just install it and allow the extender to reboot.

• Always remember not to turn it off when updating otherwise the software might get corrupt.

When to: Reset vs. Reposition

It does not require a Linksys RE7000 reset each time there is a Wi-Fi drop. Your final action must be resetting, as maybe you have just changed routers or passwords.

Under the conditions of the setup with the help of shaping on the example of the Linksys RE6300, it is more about the correct configuration. When its perfect the first time, then you can seldom have the need to repeat it unless there is a network upgrade.

Conclusion

The issues surrounding Wi-Fi may be annoyance, but most of them can be sorted out easily once you know what is happening behind the flickering lights. A clean setup of the Linksys RE6300 will provide a stable extension of the main network, and a correct set of the Linksys RE7000 will clear a number of hidden setups that can be hindering its performance.

Placement in a slow manner, maintain firmware upgrades and ensure that your devices reconnect to the correct network after each update. The steps below will enable you to have a solid, non-interrupted coverage of your home without having to purchase a new system altogether.